« previous next »
Pages: [1]   Go Down

Author Topic: RPM=Speed  (Read 17637 times)

Offline jeffhestand

  • ^ Motobrick Curious
  • Posts: 92
  • 1985 K100
RPM=Speed
« on: August 10, 2012, 02:42:04 PM »
Finally got my 85 back on the road... Of course speedo continues to defy me and not work... So.. if all of you could provide with a ball park figure that in 5th Gear at 4K RPM you are going X that would be great... This bike sure seems to want for a 6th gear as well... thanks
jeff hestand
85 K100 RT
Logged
1985 K 100... Gettin better all the time!!

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: RPM=Speed
« Reply #1 on: August 10, 2012, 02:58:22 PM »
What it "wants" is high RPMs. It is not a car or a Harley.
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline jeffhestand

  • ^ Motobrick Curious
  • Posts: 92
  • 1985 K100
Re: RPM=Speed
« Reply #2 on: August 10, 2012, 03:45:05 PM »
Frakenduck- what do you feel the optimul RPM for this engine... It does seem to want to rev and i have not pushed it too far... Maybe since the the speedo is broke and i do not know the true mileage i am a little hesitant. I have seen them sailing along on U Tube at 220 KMH.
Logged
1985 K 100... Gettin better all the time!!

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: RPM=Speed
« Reply #3 on: August 10, 2012, 03:57:53 PM »
7,000-8,000 RPM

Go ahead and bounce it off of the rev limiter.  These engines are pretty bulletproof.  (Provided you change the oil on a reasonable interval.) Half tank of fuel or more is recommended.  If you go balls out with a low tank you can starve the fuel pump since it's in the middle of the tank and the gas gets pushed to the rear.  It doesn't hurt anything, just makes for a jerky ride.

Need to make a quick pass?  Chop it down to third and let 'er rip. :yes

It's just a matter of getting used to riding it. :mbird

(Insert usual disclaimers here about riding that way on public roads.)
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline jeffhestand

  • ^ Motobrick Curious
  • Posts: 92
  • 1985 K100
Re: RPM=Speed
« Reply #4 on: August 10, 2012, 04:22:43 PM »
WOW!!!! 7 to 8K on this beast  i would be flat flyin.... on the highway at 65 or 70 what is the typical RPM( sounds like ur not at that speed much though)  :laugh
Logged
1985 K 100... Gettin better all the time!!

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: RPM=Speed
« Reply #5 on: August 10, 2012, 04:46:40 PM »
It varies by bike.  If someone chimes in with a number then be sure to verify that they have the same final drive ratio that your bike does. (Stamped into final drive right behind where it mounts to the swing arm.)
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline CubPilot

  • ^ Motobrick Curious
  • Posts: 67
Re: RPM=Speed
« Reply #6 on: August 10, 2012, 04:51:07 PM »
My will not tach more than 82-8300, and then if I hold it against the stops, it will search up and down about 300.  What should the limiter be set at?  I suppose that you have to have "special software" to set that. Best fun is Bike Week at Daytona.  Cruise up the interstate about 65-70 and let a crotch rocket or two pull out to pass and drop it in to 3rd and tach it out, right against the stops.  This K is still pulling at 135, mine, just are not big enough to see how far it will go before that little voice is asking just what the hell I think I'm doing.   It is still fun even at my age.   Those rice rockets might get there but they just won't do it as fast in the higher ranges.   You have to watch that front end as it will still come off the road at 60, and startles the hell out of me.  They don't call these things Flying Bricks without just cause! 
Logged

Offline k100

  • Motobrick Curious
  • Posts: 31
Re: RPM=Speed
« Reply #7 on: August 10, 2012, 05:21:30 PM »
i also have a bad speedo so if sumone could anser the questian that would be nice
 :beatdeadhorse: :beatdeadhorse: :beatdeadhorse:
Logged

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: RPM=Speed
« Reply #8 on: August 10, 2012, 05:23:23 PM »
Quote from: CubPilot on August 10, 2012, 04:51:07 PM
I suppose that you have to have "special software" to set that.

No software, it's a chip.  You'd either need a differently programmed chip or a programmable chip.
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline Scott_

  • Administrator
  • ^ Quintessential Motobricker
  • Posts: 2242
Re: RPM=Speed
« Reply #9 on: August 10, 2012, 06:01:13 PM »
Well, on my stock '95 1100LT, 4K rpm is 65mph.
My FD is stamped 33/12
Logged
  • My Garage
1995 K1100LT 0302044
2017 FLHTK Ultra Limited
1997 K1100LT 0302488 (R.I.P.)
1997 R1100RT ZC62149(sold)
"One who does not ask questions is ashamed to learn" Danish proverb

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: RPM=Speed
« Reply #10 on: August 10, 2012, 06:43:40 PM »
Quote from: k100 on August 10, 2012, 05:21:30 PM
i also have a bad speedo so if sumone could anser the questian that would be nice
 :beatdeadhorse: :beatdeadhorse: :beatdeadhorse:


Fix a flaky or inoperative K bike speedometer
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline wmax351

  • ^ Quintessential Motobricker
  • Posts: 1237
Re: RPM=Speed
« Reply #11 on: August 10, 2012, 08:25:50 PM »
On my stock 1991 K75, with a 32:10 rear drive, 5th gear on the fwy is 80 mph (calibrated) at 6000 rpm.

Logged
  • Albuquerque, NM
  • 91 BMW K75 Standard, 98 Moto Guzzi California EV
Bikes:
Current:1991 BMW K75 Standard, 1998 Moto Guzzi California EV11
Past: '83 BMW R65LS, '75 Honda CB550F, '69 Honda CB175, 1999 Royal Enfield Bullet 500, 1973 Triumph Tiger TR7V, 1971 BMW R75/5 in Toaster outfit, 1979 Harley Davidson XLS-1000 Sportster Roadster

Offline motodude

  • ^ SuperNatural Motobricker
  • Posts: 544
Re: RPM=Speed
« Reply #12 on: August 10, 2012, 08:32:34 PM »
Stock '90 K75RT 32:10 fd w/ no calibration, 5k rpm == 70 mph, it will run there all day long.  I've run it at 6.5k rpm continuously for hours at a time in NV no problem.

YMMV,
Tom
Logged
'95 K75RT
'90 K75RT
'87 K100RS Motorsport
No, I am not cool.  Yes, it really is the journey.

Offline BobZ(IL)

  • ^ Proficient Motobricker
  • Posts: 124
Re: RPM=Speed
« Reply #13 on: August 10, 2012, 09:45:49 PM »
Borrow a GPS and tape it to your handlebars. Make note of speed at various rpms. Also take another look at the hp/torque curve FD posted. There is a definite sweet range between 4000-6000. Thats where the fun lies.
Logged
  • Bourbonnais IL
'93 K1100LT
'78 R100S
'05 R1200GS

Offline jeffhestand

  • ^ Motobrick Curious
  • Posts: 92
  • 1985 K100
Re: RPM=Speed
« Reply #14 on: August 14, 2012, 12:38:27 PM »
well after some soul searching i decided to go ahead and install a bicycle speedo last night...For 46 bucks and am getting back speedo,, trip meter,, odometer plus another clock and avg speed and max speed ( last 2 are important to bicycle riders).. the rtv is curing today.. Ill let u know how it turns out...
Logged
1985 K 100... Gettin better all the time!!

Offline lhead

  • ^ Motobrick Curious
  • Posts: 65
Re: RPM=Speed
« Reply #15 on: August 15, 2012, 07:55:43 AM »
Hey Bro,
On the rs an indicated 60mph is ballpark 4k.
Logged
1993 K1100rs

Offline jeffhestand

  • ^ Motobrick Curious
  • Posts: 92
  • 1985 K100
Re: RPM=Speed
« Reply #16 on: August 15, 2012, 08:26:13 AM »
yeah... the bicycle speedo worked great this AM but now i am going to have to get the wheel rebalanced. Small price to pay to have a working speedo and odometer....  :bmwsmile
Logged
1985 K 100... Gettin better all the time!!

Offline sh00ter

  • ^ Proficient Motobricker
  • Posts: 320
Re: RPM=Speed
« Reply #17 on: August 15, 2012, 11:31:09 AM »
Quote from: jeffhestand on August 15, 2012, 08:26:13 AM
yeah... the bicycle speedo worked great this AM but now i am going to have to get the wheel rebalanced. Small price to pay to have a working speedo and odometer....  :bmwsmile

Ride-on time !!! Just got some myself. 
Logged
'94 1100 RS

Offline Opus

  • ^ Proficient Motobricker
  • Posts: 246
  • 1988 K100 LT
Re: RPM=Speed
« Reply #18 on: August 15, 2012, 07:55:22 PM »
Jeff, don't know if this will help but here is a link to a 1985 K100LT that can ba a parts bike.

http://lawrence.craigslist.org/mcd/3192804205.html

Plactics looks good and it has a Inst. Panel.

Just an fyi...

Opus....
Logged
Toney

1988 BMW K100LT (Current Project Bike)
1982 Honda GW 1100 I (Sold and will be missed)
1975 Honda CB550F [MOD] (Sold)
196x Sears Allstate 250 (Traded in for CB550F)
Pages: [1]   Go Up
« previous next »
Tags: