« previous next »
Pages: [1]   Go Down

Author Topic: 1992 K 100 RS 4V Final Drive very hot, noisy  (Read 12367 times)

Offline Backroad Bob

  • Curious
  • Posts: 5
  • 1992 K100 4V
1992 K 100 RS 4V Final Drive very hot, noisy
« on: March 25, 2012, 06:28:53 AM »
Hi Guys,
I recently lubed the splines on my K100, and re-assembled. A few days ago,after a short ride I decided to feel if the FD was hot. It was! Very!
 So I put the bike on it's centre stand and with the engine running and the bike in third gear, the FD is making a bit of banging and clanging. I have yet to pull the FD, and was wondering if it is the universal joint that is the culprit, and if it is, would it heat the FD to the point that it's almost too hot to the touch?

It is possible that I may have re-assembled the drive onto the shaft incorrectly, or mis-aligned when putting it all back. I did not pull the FD apart. Just lubed the splines, including the clutch spline, and re-assembled the tranny and swing arm.
As I did not check the temp of the FD prior to the lube, it may have been like this for some time.

This coming week I will remove it from the bike, but in the mean time I thought I would ask the question of you good folks to see if I am overlooking something. I am currently reading up the Clymer manual that came with the bike.

Cheers, Rob
Logged

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #1 on: March 25, 2012, 09:34:36 AM »
Did you remember to put gear oil in it?
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline Backroad Bob

  • Curious
  • Posts: 5
  • 1992 K100 4V
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #2 on: March 25, 2012, 09:37:43 AM »
I did. Castrol 80w90 gear oil. That was the first thing I checked. It is level with the top of the filler.
Logged

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #3 on: March 25, 2012, 09:49:31 AM »
Is the rotor hot too or just the FD itself?
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline DRxBMW

  • ^ SuperNatural Motobricker
  • Posts: 902
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #4 on: March 25, 2012, 09:57:40 AM »
Quote from: frankenduck on March 25, 2012, 09:49:31 AM
Is the rotor hot too or just the FD itself?

Rear Brembo pads tend to drag, thus generating heat.

Didn't you catch a brake on fire Duck ?  Or was that someone on the KBMW list ?
Logged
Gary
Williamsport,Pa

1994 K 75 ABS "custom"
2005 F 650 GS

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #5 on: March 25, 2012, 10:10:23 AM »
No, that was a dipsh*t potential buyer who I let test ride the bike and was too f'n stupid to pull over when the rear brake locked up.  Eventually the rotor got hot enough to ignite the nearby final drive boot. :yow

Mystic R-o-d did one too. :neener:

Warning:  If you set the rear brake lever too tightly and apply the brake hard then it will cause the piston of the rear master cylinder to get snagged on its set screw and "lock" the rear brake.  Always leave a little play in the rear brake.
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Rick G

  • Guest
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #6 on: March 25, 2012, 09:26:08 PM »
I have seen uni joints glowing red hot before letting go so it well could be that. Probably best to have a look and be sure as the rear uni does let go sometimes and better to be safe than sorry.
Munichs in WA can do a replacement uni and you are relativly close to them.
Logged

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #7 on: March 25, 2012, 09:31:19 PM »
Quote from: Rick G on March 25, 2012, 09:26:08 PM
Munichs in WA

Who/where is this?  :confused:
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline robleyd

  • ^ Proficient Motobricker
  • Posts: 138
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #8 on: March 25, 2012, 11:51:48 PM »
WA = Western Australia, not Washington State. Munich = Munich Motorcycles in said (Australian) state.
Logged
Motobrick member #70
1996 K1100 LT
1969 Triumph Bonneville

Offline frankenduck

  • Adrninistrator
  • ^ Quintessential Motobricker
  • Posts: 5511
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #9 on: March 26, 2012, 12:05:19 AM »
My bad.  I live in Washington so that's what leaps to mind when I see WA.
Logged
Once I had a Collie pup. Dug a hole and covered him up. Now I sit there by the hour. Waiting for a Collie-flower.
New to K bikes? Click here.
K Bike Maintenance & Mods: Click here.
Buy parts here.

Offline robleyd

  • ^ Proficient Motobricker
  • Posts: 138
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #10 on: March 26, 2012, 02:41:59 AM »
Heh; pretty much the same here - if I see SA I don't think South Africa  :lol:
Logged
Motobrick member #70
1996 K1100 LT
1969 Triumph Bonneville

Rick G

  • Guest
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #11 on: March 26, 2012, 03:41:35 AM »
Oops note to self dont confuse the people in other countries :embarass:
Logged

Offline robleyd

  • ^ Proficient Motobricker
  • Posts: 138
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #12 on: March 26, 2012, 07:08:26 AM »
Yeah, remember that the US is the world  :hmm:
Logged
Motobrick member #70
1996 K1100 LT
1969 Triumph Bonneville

Offline DRxBMW

  • ^ SuperNatural Motobricker
  • Posts: 902
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #13 on: March 26, 2012, 07:36:11 AM »
Quote from: Rick G on March 25, 2012, 09:26:08 PM
I have seen uni joints glowing red hot before letting go so it well could be that. Probably best to have a look and be sure as the rear uni does let go sometimes and better to be safe than sorry.
Munichs in WA can do a replacement uni and you are relativly close to them.

Are there ANY clicking noises emanating from the UJ Bob ?

Most UJ's sound a forewarning before failure/total meltdown.
Logged
Gary
Williamsport,Pa

1994 K 75 ABS "custom"
2005 F 650 GS

Offline Backroad Bob

  • Curious
  • Posts: 5
  • 1992 K100 4V
Re: 1992 K 100 RS 4V Final Drive very hot, noisy
« Reply #14 on: March 26, 2012, 07:44:37 PM »
Follow up:

Guys, I rang Munich Motorcycles in W.A. ( Western Australia) LOL!  who were quite helpful.
Said that I am going to hear a bangin' an a clangin' when the bike is in gear and driving the rear wheel with no load on it.
Well, not so much bangin' an clangin', but the drive would be noisy, but only when under no load.
I asked about the heat, and was told they do get quite warm, and not to worry unduly about that. ( we were two up at the time.)
I pulled the FD and checked the universal joint visually, and physically. Could not detect any movement, or hear any clicking. It other words, it felt tight when rotated back and forth.
I added a little extra moly to the spline which is in v. good shape, and re-assembled.
So from now on, I will be watching my FD very closely, and will post if anything changes.
One of those infra red lazer temp probe thingys would be good to use in a situation like this. I might check it out.
Thanks for the replies everyone.............appreciated.

Cheers, Rob
Logged
Pages: [1]   Go Up
« previous next »
Tags: